Normand

Since 1950
Home Categories Shop machines Dust collectors Dust collectors Dust Collector 3HP-220V 1 Micron Steel City 80-310S3C
Description

Nowadays, for the majority of cabinetmakers, the main battle is eliminating dust. Working soft, hard or exotic woods, or working particles board or MDF panels, chips and dust are finer, more plentiful and more aggravating.

How serious are the problems created by wood dust? It will depend on how long you are machining wood in an enclosed area. Because it is proven, prolonged exposure is potentially dangerous and can cause very significant respiratory problems.

While table saws and planers are machines that require a lot from a dust collector, sanders produce a lighter dust that requires excellent filtration.

A safe and affordable solution would be to get a single stage dust collector that would be powerful enough. That’s what Steel City offers, a full range of industrial dust collectors that can adapt to the needs and budget of everyone.

  • All units are on trolley with swivel castors to allow easy and quick travel where it's needed. Remember that the closer a dust collector is to the machines, the better the performance.
  • All units are supplied with 20"(500mm) dia plastic collection bag and a quick attachment metal strap that allows to better visualize the fill level and facilitates garbage disposal.
  • All units are supplied with totally enclosed induction motor for continuous industrial use with safety lock key switch.
  • All units are fitted with fully metal frame and duct connected to a collecting port equipped with aluminum alloy impeller to reduce the risk of sparks. The port inlet is protected by a wire screen to prevent access of large pieces.

Available in 3 filtering versions: B / C / H

B-    Felted fabrics woven bag tight enough to capture dust above 2 microns. Metal support and clamp included.

C-    Pleated and non-woven polyester made cartridge that can capture dust above 1 micron. Metal clamp included.

It offers a filtering area 5 times larger than a standard filter bag which reduces the frequency of cleaning.

It is provided with an external arm which rotates 120 ° and operates an internal flexible flapper that rattles the filter’s pleats to dislodge dust which then falls down into the collecting bag.

H-    High-efficiency HEPA cartridge that can capture dust above 0.3 micron. Metal clamp included.

Such a cartridge can hold up to 99.9% of fine particles of dust.

It is provided with an external arm which rotates 120 ° and operates an internal flexible flapper that rattles the filter’s pleats to dislodge dust which then falls down into the collecting bag.

In addition, the 80-310S3C model is characterised by:

  • Double collecting bags
  • 3HP – 220V/1Ph powerful motor
  • Air flow capacity: 2280CFM
  • C- 1 micron standard cartridge with clamp (kit of 2)
  • Dust inlet: 7"(180mm)) dia with 3 x 4"(101mm) dia connector and 2 caps
  • Overall size: 60"(150cm) long x 32"(80cm) wide x 71"(180cm) high
  • Weight: 220lbs (100kg)

 

You may also be interested in the following product(s)

    Reg.$479 99
    0.3 Micron HEPA Cartridge Centurion 82008
    0.3 Micron HEPA Cartridge Centurion 82008
    Reg.$24 99
    Dust Separator Centurion 82-010
    Dust Separator Centurion 82-010
    Reg.$89 99
    Dust Collection Kit-17 pieces Centurion A50055
    Dust Collection Kit-17 pieces Centurion A50055
    Reg.$4 49
    20" Dust Collection Bag Centurion BAG204101
    20" Dust Collection Bag Centurion BAG204101

A word from the boss 

WMS-2019: Mission accomplished! (19-11-07)

Once again this year, Normand participated in the WMS-2019 National Fair, the most important industrial fair intended exclusively for the Canadian secondary wood processing industry.

Normand was again one of the major exhibitors of this major biannual exhibition, which was held from October 2 to November 1 at the International Center in Toronto.

Our participation was summed up as follows: 750 000 dollars of equipment carried in four 53ft trailers and demonstrated on 3100 ft² of floor space thanks to the support of a team of 25 people.

In addition to some of the state-of-the-art equipment showed, we took the opportunity to spread the full range of Steel City™ machines (more than 50 models) thus confirming the important place acquired by this brand in recent years.

In short, this major investment and the results that should result from it allow us to say: Mission accomplished!

Click here to take a look at the pictures